Computer

This is how you should NOT mount an all-in-one liquid cooler

The mounting of the all-in-one liquid cooling (RL IAO) is very important, as it can cause problems in the future. An incorrect installation can lead to the breakage of the liquid cooling pump. If this does not work, the water does not flow through the circuit and, therefore, the processor will not cool.

Micro evaporation, something that nobody tells you

Without going into deep physics, after the rain or after scrubbing, the floor dries up little by little. It is not necessary to reach temperatures of 100 °C for the water to start evaporating. Over time, the water evaporates until the soil is completely dry. A process that can occur both at 10º C and at 30 °C, although at different speeds.

Within a liquid refrigeration we have distilled water, from which most of the impurities have been removed. This is mainly done to prevent the water from deteriorating and bacteria or even moss from growing.

custom dual reservoir liquid cooling system

This distilled water is normally subjected to temperatures above 50 °C, so not always in liquid state. Within the circuit there may be a small proportion of it that is in gaseous state.

The gum of the hoses of liquid cooling they have holes extremely small, practically invisible. The water does not escape through them because it has a larger volume, so to speak (it is somewhat more complex). But actually the water escapes very slowly.

Little by little the water evaporates without us noticing. This in a custom liquid cooling is not a problem, since we can see the level of water in the circuit and fill it if necessary. The problem is in the all-in-one models, where we cannot see its water level. The tubes, the radiator and the pump are opaque, in addition, there is no reservoir.

How should I install my liquid cooling to avoid damage?

There is neither a repository nor a window in a RL AIO that allows us to see the amount of liquid in the system. As if that were not enough, the vast majority of these kits They do not have a filler cap. A set of conditions that, added to an incorrect installation, can lead to disaster.

The correct installation of an all-in-one liquid cooler on the front of a PC tower is with the tubes at the bottom. The reason is that in this way the pump will suffer less as the amount of liquid in the circuit decreases.

assembly of an all in one liquid refrigeration in an incorrect way

Here we can see how you never have to mount an all-in-one refrigeration

If we install it with pipes near the top of the PC chassis, we will have a problem. The pump will need more force so that the circuit continues to function normally. In addition, the amount of liquid that circulates will fall, being able to generate bubbles. This assumes that there will be times when the distilled water does not “absorb” the heat generated by the processor.

Install liquid cooling with the tubes in the bottom does not guarantee that it will last longer. With this we make the pump work more comfortably, but in the long run it will die due to micro-evaporation and not being able to fill it.

If you want our advice, or you ride one custom liquid cooling or you leave problems with a air sink. The best solution, without a doubt, is an air cooler. The maximum that can happen is that the fan breaks, being able to change it in a moment, since these fans are of standard size (they are usually 92 mm or 120 mm).

Correct mounting of an all-in-one liquid cooler

Bad practices of manufacturers and assemblers

It is possible that when you go to install one of these RL AIO tand you find that you can not install it correctly. The usual thing is that the tubes are short and we can’t install them down, we may have to install it wrong. It is not something exactly rare, moreover, few brands have RL AIOs with long tubes that allow optimal installation.

Currently, the vast majority of computer gaming chassis already support radiators on the top of up to 240 mm, or even more. We can install it at the top and thus solve the problem of short tubes.

Our advice is that if you install it at the top, do it with a slight incline. You can go to a hardware store and buy slightly longer bolts and some washers to create that slight slant. This will allow the water to always go to the tubes, even with the micro evaporation of the liquid.

There are also computer stores, which for convenience, wrongly mount them. Especially large surfaces, where they presume not to be fools, mount them upside down. It is possible that it is due to ignorance or to guarantee work for the future. If you find an incorrectly mounted RL AIO, better find another computer store where to buy the computer.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *